Home >> Plate Roller >> 3 Roller Bending Machine >> Hydraulic symmetrical 3-roll plate bending machine

3 roller bending machine, pyramid roller, hydraulic plate bending machine

3 roller bending machine, pyramid roller, hydraulic plate bending machine
Hydraulic symmetrical 3-roll plate bending machine

Modelmax. plate thicknessmax. plate widthrolling speedfull-loading min. rolling diameterupper roller diameterlower rollers diametermain motor powercentral distance of two lower rollers
mmmmm/mmmmmmmmkwmm
W11Y-16*20001620004.55502602207.5320
W11Y-16*25001625004.560028024011360
W11Y-20*20002020004.560028024011360
W11Y-20*25002025004.570034026015430
W11Y-25*25002525004.575036027018.5480
W11Y-30*25003025004.590040032022550
W11Y-30*30003030004.590043035030600
W11Y-40*25004025004.5100048038037600
W11Y-40*32004032004.5110054044045700
W11Y-50*25005025004.5120056046045700
W11Y-50*30005030004.5120058048055750
W11Y-60*25006025004130060051055750
W11Y-60*30006030004130062053055800
W11Y-70*30007030004140068059075850
W11Y-80*30008030004150075066075900
W11Y-90*300090300041600780680901000
W11Y-100*300010030003.51700830740901000
W11Y-110*300011030003.518008807901101080
W11Y-120*300012030003.520009208301101160
W11Y-120*400012040003.520009608501321160
W11Y-150*300015030003.5220010009001501280
W11Y-160*300016030003.5250010609201501280
W11Y-180*300018030003.5250010809501801360
W11Y-200*300020030003.5250011209802201420

Hydraulic symmetrical 3-roll plate bending machine

Description

3 roller bending machine
3 roller bending machine

The hydraulic symmetrical three roller steel bending machine structure is three roller symmetry, the vertical lifting movement and in two roller symmetrical position in the center, through the action of hydraulic oil in the hydraulic cylinder piston is obtained for hydraulic transmission.

Characteristics:

1.The lower roller of the upper roller and the lower roller of the lower roller is provided with an upper and lower supporting roller support. According to the load of the rolled products, the roller of the lower part of the lower roller is adjusted, and the linear degree of the product is greatly improved.

2.NC control, high production efficiency, Under the sporty NC roll on roll, greatly improve the efficiency. This machine only needs one person to operate, and the operation is simple.

3.Three Roller Symmetrical Bending Machine (belt roller) with three roller bending machine has a small center distance can get shorter coil end straight edge, ensure good roll roundness.

4.With the rolling machine roller adopts horizontal hydraulic sheet metal bending machine device, convenient operation of the coil increases, reduce the wrong side and angle, improve the precision of bending.

Working principle

3 roller bending machine
3 roller bending machine

Used at room temperature for the plate rolled into a cylindrical, circular arc, conical performance. Superior, compact structure, easy to operate. On the roller lift, overturned device using hydraulic drive. The main drive by the motor through the transmission with the triangle, the reducer driven by two roller drive, rolling flexible. Using PLC programmable display control, the use of displacement sensors on the roller lift check, the measured value showed that the table shows. Improve product efficiency and product quality, overturned frame with hydraulic overturned.

Hydraulic symmetrical three roller steel rolling machine relative to the mechanical bending machine high efficiency, the disadvantage is that the remaining plate head coil required school or pre-bending with other equipment.

The device can roll thick 1MM-200mm, board width 8000 mm sheet.

Performance:

3 roller bending machine
3 roller bending machine

The construction of this machine is in the from of three roller symmetry.The top roller,in the central symmetr position over the two bottom rollers,does vertical motion up and dow through screw,nut and worm transmission.Decelerator gears bottom rollers providing torsion moment for coiling sheet metal.The construction of the machine is compact and the operation and maintenance is convenient.